Dual In-Tank Pump System, Typhoon, Blazer, Jimmy 1050LPH

DPFS-TY1050 - 1050 LPH E100 Dual In-Tank Fuel System 1992-1994 Chevrolet GMC Typhoon, S10 Blazer, Jimmy, Bravada

FEATURES:

• CnC Billet T6 Aluminum Modular Dual Fuel Pump Hanger
• 2 x Walbro F90000285 525 LPH (Hellcat) E85 Fuel Pumps
• Weatherproof 100% plug & play heavy-duty wiring harness
• Massive -10 AN ORB feed port, -6 AN ORB return port
• Dedicated pump circuits with new 6-way bulkhead connector
• Includes a new stainless-steel locking ring, OE-type tank gasket
• 90 ohm ceramic level sender resistor (analog dash - standard)
• Multiple optional feed & return port configurations

*SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Recommended fuel system requirements:
-10 PTFE feed line, -6 PTFE return lines with a #12 filter housing + 10-micron element

Upgraded lines are required with this 1050 LPH system!

HD HARNESS FEATURES:

• Plug & Play (no cutting or splicing required)
• Weatherproof factory connectors
• Heavy-gauge automotive-grade copper wire on main power feeds and intermediate harness
• Heavy-duty weatherproof relays mount behind fuel tank (no under-hood clutter)
• Weatherproof dual fuse holder with stainless bracket (mounts on back of alternator)
• Pump power indicator lamp outputs
• Swap-able primary / secondary pump ground control connectors
• Alternator-direct power for maximum pump performance
• Silicon grease, spare fuse, wire ties included
• Stainless steel mounting hardware
• 15 PSI Hobbs pressure standard switch with interface harness (optional 4, 7 and 10PSI)
• Body ground upgrade with battery nuts (included)

APPLICATION QUESTIONS:

Q. Is the Hobbs pressure switch included with the DP system?
A. A 15 PSI Hobbs pressure switch and interface harness are included with the system as standard equipment. 15 PSI is the best pressure at which to activate the secondary fuel pump in most V6 Turbo Typhoons. Ideally the secondary pump should be activated approximately 100 HP shy of the primary pump running out of fuel to prevent pressure spikes or lean conditions. Some customers have computers which can control both pumps via the jumpers (shown in our picture) on our dual harness. Some customers have upgraded return lines and chose to run both pumps all the time. We recommend using either your computer or our Hobbs switch to control the secondary pump. This reduces the electrical load, fuel heating and wear on the secondary pump. The primary and secondary pump may be easily switched by swapping the control jumpers if you wish to balance out the run-time on the pumps. The DP harness comes with both control jumpers plugged in as shown in our ad. In addition to this the DP harness comes with a Weather-Pack connector so you can interface the secondary pump control to your aftermarket computer or any pull-to-ground signal.

Q. Can other pumps be used in the DP sender as an option?
A. This hanger can accommodate any 38 mm body pump such as a 255, 340, 450 or 525 LPH pump in single or dual configuration.
NOTE: WE DO NOT ACCEPT CUSTOMER-SUPPLIED PUMPS TO BE INCORPORATED INTO OUR DP SYSTEM PERIOD!

Q. Is this DP system E85 compatible?
A. The DFPS-TY1050 DP hanger uses Walbro F90000285 pumps which are 100% Ethanol compatible. True E85 factory certified systems have their electrical connections fully isolated from the fuel which is impossible given the age of these trucks and the tank design. Modern E85 Flex-Fuel systems are manufactured with special plastics and metals. Fuel system health will impact pump life.

Q. Can I buy the entire DP system in a D-I-Y format?
A. We DO NOT offer this item as a D-I-Y kit.

Q. I already have some other pumps. Can I use them with your system?
A. NOTE: DUE TO PROBLEMS WITH CUSTOMER SUPPLIED PUMPS AND PRODUCTION FLOW ISSUES WE DO NOT ACCEPT CUSTOMER-SUPPLIED PUMPS TO BE INCORPORATED INTO OUR DP SYSTEM NOR DO WE OFFER IT LESS PUMPS. ALL DP SYSTEMS ARE SOLD AS COMPLETE TESTED SYSTEMS.

Q. What size of fuel lines do you recommend with this system?
A. We recommend conductive PTFE (Teflon) braided -8 feed and a -6 return lines minimum. We do not recommend any type of rubber (braided or not) for use with modern-day fuels. These PTFE (Teflon) lines will be able to support over 90% of the full performance of this DP systems. For maximum performance we recommend a -8 feed line.

Q. Where is the biggest restriction in the fuel system?
A. The factory steel lines running up the front of the motor.

Q. Can I use a volt-booster with your system?
A. Yes, we recommend a voltage booster for increased system voltage which benefits pump performance under WOT only.

Q. What brand of fuel pressure regulator do you recommend?
A. Racetronix REG-G7B (factory location / best option) or Racetronix REG-FI886 universal regulator with aftermarket fuel rail configurations.

Q. Where do I get support and installation information?
A. All technical and warranty support for this system is provided via our Racetronix support forum ONLY!

Q. What are the performance specs of the DP system?
A. These are the typical test bench specs with 2 x Walbro F90000285 fuel pumps using stoddard solvent @ 20°C:
• x LPH @ 43.5psi @ 14.0v @ x A
• x LPH @ 43.5psi @ 16.0v @ x A
• x LPH @ 80.0psi @ 14.0v @ x A
• x LPH @ 80.0psi @ 16.0v @ x A

Q. How much HP will this system support ? (Will it support my HP requirements?)

A. Multiply your HP by 0.42 which will give you the required fuel in LPH with a 20% safety margin. You must consider the flow at your maximum boost pressure. For example, if you base fuel pressure is 43.5 PSI and your your regulator increases 1 LB of fuel pressure for every 1 LB of boost and you run 20 PSI of boost your maximum fuel pressure would be 63.5 PSI. Using the flow data above, confirm that the DP system is able to provide the required flow at your maximum fuel pressure and voltage. This calculation does not factor restrictions in the fuel lines. Since the condition of each system tends to vary it is best to run a return flow test at max fuel pressure once the DP is installed to determine if upgrading the fuel lines is required.

Q. Are there higher flowing pumps that I can substitute in this system?
A. The Walbro F90000285 525 LPH (Hellcat) pumps are the highest flowing available at this time.